ZyXEL SBG3300 Bootlog
HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
STRF
400H
PHYE
DDR2
SIZ4
SIZ3
SIZ2
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.38-112.118 for BCM963268 (32bit,SP,BE)
Build Date: 01/14/2015 (allen@allen-VirtualBox)
Copyright (C) 2000-2011 Broadcom Corporation.
NAND flash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB
External switch id = 53125
Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
Checking Reset button on EXT INTR 0
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-20) : 963168MXH_17A
Number of MAC Addresses (1-32) : 12
Base MAC Address : e8:37:7a:3e:90:92
PSI Size (1-128) KBytes : 1024
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
Port 4 link UP
0
Wait for Multiboot Service Packet... 0
Booting from latest image (0xb8040000) ...
Code Address: 0x80020000, Entry Address: 0x8035c2e0
Decompression OK!
Entry at 0x8035c2e0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x8035c2e0
Linux version 2.6.30 (rune@rune-VirtualBox) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 SMP PREEMPT Thu Mar 31 17:22:27 CST 2016
NAND flash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB
963168MXH_17A prom init
CPU revision is: 0002a080 (Broadcom4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
memory: 07ece000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00007ece
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00007ece
On node 0 totalpages: 32462
free_area_init_node: node 0, pgdat 8046aa80, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 222 pages used for memmap
Normal zone: 28144 pages, LIFO batch:7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208
Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 512 (order: 9, 2048 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 123064k/129848k available (3345k kernel code, 6612k reserved, 1068k data, 156k init, 0k highmem)
Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 Mar 31 2016 16:53:53
CPU revision is: 0002a080 (Broadcom4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
Brought up 2 CPUs
net_namespace: 1140 bytes
NET: Registered protocol family 16
Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (00008a63-00008a7c=-25<300)
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff]
pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff]
pci 0000:00:00.0: supports D1 D2
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: disabled
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Mar 31 2016 16:56:34 initialized
Broadcom GBPM v0.1 Mar 31 2016 16:56:34 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.11)
msgmni has been set to 240
io scheduler noop registered (default)
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
Broadcom DSL NAND controller (BrcmNand Controller)
-->brcmnand_scan: CS=0, numchips=1, csi=0
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
Disabling XOR on CS#0
brcmnand_scan: Calling brcmnand_probe for CS=0
B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=01f1001d
After: NandSelect=40000001, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 6574845b
timing2 not adjusted: 00001e96
brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010
BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0
Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=01f1001d, tim1=6574845b, tim2=00001e96
BrcmNAND version = 0x0400 128MB @00000000
brcmnand_scan: Done brcmnand_probe
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
100 CS=0, chip->ctrl->CS[0]=0
ECC level 15, threshold at 1 bits
reqEccLevel=0, eccLevel=15
190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010
brcmnand_scan 10
200 CS=0, chip->ctrl->CS[0]=0
200 chip->ecclevel=15, acc=f7ff1010
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
brcmnand_scan 220
Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000
brcmnand_scan 230
brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000
brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
300 CS=0, chip->ctrl->CS[0]=0
500 chip=87a56d90, CS=0, chip->ctrl->CS[0]=0
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 not found for chip on CS0
Bad block table 1tbB not found for chip on CS0
File system address: 0xb8040000
Scanning device for bad blocks, options=00004000
-->brcmnand_isbad_raw(offs=7fe0000
Bad block table written to 0x07fe0000, version 0x01
-->brcmnand_isbad_raw(offs=7fc0000
Bad block table written to 0x07fc0000, version 0x01
brcmnandCET: Did not find CET, recreating
brcmnandCET: Status -> Deferred
brcmnand_scan 99
Root file system size 3a80000
bad block number = 0
Creating 3 MTD partitions on "brcmnand.0":
0x000000040000-0x0000016a0000 : "rootfs"
0x000007b00000-0x000007f00000 : "data"
0x000000000000-0x000000020000 : "nvram"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=900 sec (nowayout= 0)
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x4007 is enabled
PCIe: No device found - Powering down
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v2.2 Mar 31 2016 16:54:33 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Mar 31 2016 16:54:33
bcmPktDma_init: Broadcom Packet DMA Library initialized
Total # RxBds=1448
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.5 Mar 31 2016 16:56:19
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem) readonly on device 31:0.
Freeing unused kernel memory: 156k freed
Empty flash at 0x0000a014 ends at 0x0000a800
Empty flash at 0x0001507c ends at 0x00015800
Empty flash at 0x000bb1b8 ends at 0x000bb800
Empty flash at 0x00306028 ends at 0x00306800
jffs2_scan_eraseblock(): Node at 0x00310ff8 {0x1985, 0xe002, 0x00000243) has invalid CRC 0x1985e002 (calculated 0x08bdd51f)
Loading drivers and kernel modules...
JFFS2 notice: (230) check_node_data: wrong data CRC in data node at 0x00305fb4: read 0xfba74207, calculated 0xa545ca7b.
chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
Broadcom Ingress QoS Module Char Driver v0.1 Mar 31 2016 16:54:33 Registered<243>
Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9532, buf size=2112
Broadcom BPM Module Char Driver v0.1 Mar 31 2016 16:54:27 Registered<244>
[NTC bpm] bpm_set_status: BPM status : enabled
JFFS2 notice: (230) check_node_data: wrong data CRC in data node at 0x0031b698: read 0x492b3ad1, calculated 0x440bccd8.
chipId 0x631680D0
Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Mar 31 2016 16:54:28 Registered <241>
FAP Debug values at 0x00000010 0x00000010
Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
FAP Debug values at 0xa5c5b840 0xa5c9b840
Allocated FAP0 GSO Buffers (0xA5C61C98) : 1048576 bytes @ 0xA5D00000
Allocated FAP1 GSO Buffers (0xA5CA1C98) : 1048576 bytes @ 0xA5E00000
Allocated FAP0 TM SDRAM Queue Storage (a5c61c9c) : 219456 bytes @ a5cc0000
Allocated FAP1 TM SDRAM Queue Storage (a5ca1c9c) : 219456 bytes @ a5f00000
[NTC fapProto] fapReset : Reset FAP Protocol layer
[FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6600>, free <56>, total<8192>
[FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6600>, free <56>, total<8192>
[FAP0] PSM : addr<0x80002000>, used <24512>, free <64>, total <24576>
[FAP1] PSM : addr<0x80002000>, used <24512>, free <64>, total <24576>
[FAP0] Flows supported: 226 (dsp 56, psm 45, qsm 125)
[FAP1] Flows supported: 226 (dsp 56, psm 45, qsm 125)
[FAP0] DQM : availableMemory 14680 bytes, nextByteAddress 0xE00106A8
[FAP1] DQM : availableMemory 14680 bytes, nextByteAddress 0xE00106A8
[FAP0] GSO Buffer set to 0xA5D00000
[FAP1] GSO Buffer set to 0xA5E00000
[FAP0] FAP BPM Initialized.
[FAP1] FAP BPM Initialized.
fapDrv_construct: FAP0: pManagedMemory=b0820710. wastage 8 bytes
fapDrv_construct: FAP1: pManagedMemory=b0a20710. wastage 8 bytes
bcmPktDma_bind: FAP Driver binding successfull
[FAP0] FAP TM: ON
[FAP1] FAP TM: ON
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63168D0 Ethernet Network Device v0.1 Mar 31 2016 16:56:13
Broadcom GMAC Char Driver v0.1 Mar 31 2016 16:56:17 Registered<249>
Broadcom GMAC Driver v0.1 Mar 31 2016 16:56:17 Initialized
fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a20710 bytes remaining 7000
ETH Init: Ch:0 - 200 tx BDs at 0xb0a20710
bcmPktDma_EthInitTxChan_Dqm LINE 97
bcmPktDma_EthInitTxChan_Dqm LINE 109
bcmPktDma_EthInitTxChan_Dqm LINE 117
bcmPktDma_EthInitTxChan_Dqm LINE 120
bcmPktDma_EthInitTxChan_Dqm LINE 122
fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b0820710 bytes remaining 7000
ETH Init: Ch:1 - 200 tx BDs at 0xb0820710
bcmPktDma_EthInitTxChan_Dqm LINE 97
bcmPktDma_EthInitTxChan_Dqm LINE 109
bcmPktDma_EthInitTxChan_Dqm LINE 117
bcmPktDma_EthInitTxChan_Dqm LINE 120
bcmPktDma_EthInitTxChan_Dqm LINE 122
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b08216b0 bytes remaining 2184
ETH Init: Ch:0 - 600 rx BDs at 0xb08216b0
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a216b0 bytes remaining 2184
ETH Init: Ch:1 - 600 rx BDs at 0xb0a216b0
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth3: MAC Address: E8:37:7A:3E:90:92
eth2: MAC Address: E8:37:7A:3E:90:92
eth1: MAC Address: E8:37:7A:3E:90:92
eth0: MAC Address: E8:37:7A:3E:90:92
eth4: MAC Address: E8:37:7A:3E:90:92
eth5: MAC Address: E8:37:7A:3E:90:92
BCM63XX_USB USB Device not present
insmod: can't insert '/lib/modules/2.6.30/extra/bcm_usb.ko': No such device
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: high_wmark_tot=6195
PCI: Setting latency timer of device 0000:00:00.0 to 64
wl: passivemode=1
wl: napimode=0
wl0: allocskbmode=1 currallocskbsz=512
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm6362_map.bin
srom rev:8
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L06B.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
ifconfig: SIOCGIFFLAGS: No such device
===== Release Version 4.12L.06B (build timestamp 160331_1722) =====
Fri Jan 1 00:00:00 UTC 2016
Note: Loading 6300 MDK (default) driver for 63168 chip
Note: Forcing 53115 driver for 53125
Switch MDK: num_switches = 2
Switch MDK: unit = 0; phy_pbmp = 0x18; config_pbmp = 0x58
Switch MDK link poll thread: unit=0; phypbmp=0x18
AutoNeg is diseth5 (switch port: 12) Link DOWN.
abled and Speed message received before monitor task is initialized kerSysSendtoMonitorTask
has changed
Switch MDK link poll thread: unit=1; phypbmp=0x1e
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16000 buckets, 16000 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip6tables v1.4.0: can't initialize ip6tables table `nat': Table does not exist (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
iptables: No chain/target/match by that name
Sntp: Using new rule CET-1CEST,M3.5.0/1:0,M10.5.0/1:0
MDK.0> 1:
MDK.1> seti reg 0x3400 0xe3
MDK.1> exit
MDK.0> 1:
MDK.1> vlan create 1
MDK.1> exit
MDK.0> 1:
MDK.1> vlan add 1 8
MDK.1> exit
MDK.0> 1:
MDK.1> vlan add 1 4 untag
MDK.1> exit
MDK.0> 1:
MDK.1> pvlan 4 1
MDK.1> exit
MDK.0> 1:
MDK.1> vlan add 1 3 untag
MDK.1> exit
MDK.0> 1:
MDK.1> pvlan 3 1
MDK.1> exit
MDK.0> 1:
MDK.1> vlan add 1 2 untag
MDK.1> exit
MDK.0> 1:
MDK.1> pvlan 2 1
MDK.1> exit
MDK.0> 1:
MDK.1> vlan add 1 1 untag
MDK.1> exit
MDK.0> 1:
MDK.1> pvlan 1 1
MDK.1> exit
interface usb0 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
[th_dhcp_func][659] Second thread start, th_id(1026), pp_id(1471)...
[udhcpd][1233] Thread created, th_dhcp(1026)!!!!
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
Created new Tag Rule: dev=eth0, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth0, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth0, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth0, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth0, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth0, dir=1, tags=2, id=0
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
Created new Tag Rule: dev=eth0, dir=0, tags=1, id=1
Created new Tag Rule: dev=eth0, dir=0, tags=2, id=1
Created new Tag Rule: dev=eth0, dir=1, tags=0, id=1
Created new Tag Rule: dev=eth0, dir=1, tags=1, id=1
Created new Tag Rule: dev=eth0, dir=1, tags=2, id=1
Created new Tag Rule: dev=eth1, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth1, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth1, dir=1, tags=2, id=0
Created new Tag Rule: dev=eth1, dir=0, tags=1, id=1
Created new Tag Rule: dev=eth1, dir=0, tags=2, id=1
Created new Tag Rule: dev=eth1, dir=1, tags=0, id=1
Created new Tag Rule: dev=eth1, dir=1, tags=1, id=1
Created new Tag Rule: dev=eth1, dir=1, tags=2, id=1
Created new Tag Rule: dev=eth2, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth2, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth2, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth2, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth2, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth2, dir=1, tags=2, id=0
Created new Tag Rule: dev=eth2, dir=0, tags=1, id=1
Created new Tag Rule: dev=eth2, dir=0, tags=2, id=1
Created new Tag Rule: dev=eth2, dir=1, tags=0, id=1
Created new Tag Rule: dev=eth2, dir=1, tags=1, id=1
Created new Tag Rule: dev=eth2, dir=1, tags=2, id=1
Created new Tag Rule: dev=eth3, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth3, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth3, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth3, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth3, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth3, dir=1, tags=2, id=0
Created new Tag Rule: dev=eth3, dir=0, tags=1, id=1
Created new Tag Rule: dev=eth3, dir=0, tags=2, id=1
Created new Tag Rule: dev=eth3, dir=1, tags=0, id=1
Created new Tag Rule: dev=eth3, dir=1, tags=1, id=1
Created new Tag Rule: dev=eth3, dir=1, tags=2, id=1
Created new Tag Rule: dev=eth5, dir=0, tags=0, id=0
Created new Tag Rule: dev=eth5, dir=0, tags=1, id=0
Created new Tag Rule: dev=eth5, dir=0, tags=2, id=0
Created new Tag Rule: dev=eth5, dir=1, tags=0, id=0
Created new Tag Rule: dev=eth5, dir=1, tags=1, id=0
Created new Tag Rule: dev=eth5, dir=1, tags=2, id=0
ifconfig: SIOCGIFFLAGS: No such device
interface usb0 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
WLmngr Daemon is running
optarg=0 shmId=0
wlevt is ready for new msg...
interface wl1 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
Vendor serial number = E8377A3E9092 SBG3300 1.01AAIW4
Could not get lock!
ssk:error:60.493:mdm_activateObjects:1059:rcl handler reports error=1 on X_001349_L2tpCfg {}
There is no Predefined DevicePin in CFE
Enter user spaceStarting multiwan wrapper......
Starting vpnuser......
Starting ipsec wrapper......
Starting watcher......
=====> multiwan_cms: init fifo
ssk:error:70.914:initWanLinkInfo:701:==> adding wanLinkInfo at {1}, atm=1 ptm=0 eth=0 moca=0 gpon=0 epon=0 lte=0
ssk:error:70.916:initWanLinkInfo:701:==> adding wanLinkInfo at {2}, atm=0 ptm=1 eth=0 moca=0 gpon=0 epon=0 lte=0
l2tp_cms.c-setWrapperDebugLevel()-1009:set wrapper debug level to 3
Starting celld daemon......
pptp_cms.c-main-Starting pptp wrapper at Fri Jan 1 00:00:49 UTC 2016
l2tp_cms.c-main-Starting l2tp wrapper at Fri Jan 1 00:00:49 UTC 2016
Setting SSID: "webmario"
Setting SSID: "ZyXELE9092_Guest1"
Setting SSID: "ZyXELE9092_Guest2"
Setting SSID: "ZyXELE9092_Guest3"
Chanspec set to 0x100b
wlctl: Unsupported
=====> multiwan_cms: check app
=====> multiwan_cms: kill old orphan app
Auto-negotiation enabled.
Link is down
ssk:error:72.981:initWanLinkInfo:701:==> adding wanLinkInfo at {3}, atm=0 ptm=0 eth=1 moca=0 gpon=0 epon=0 lte=0
ssk:error:72.982:initWanLinkInfo:701:==> adding wanLinkInfo at {7}, atm=0 ptm=0 eth=0 moca=0 gpon=0 epon=0 lte=0
killall: multiwan: no process killed
=====> multiwan_cms: killall returned 256
=====> multiwan_cms: start app
=====> multiwan_cms: start app
=====> multiwan_cms: open fifo for read
=====> multiwan_cms: open fifo for write
=====> multiwan_cms: open fifo for read
=====> multiwan_cms: open fifo for write
=====> multiwan_cms: open log fifo for read
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
ssk:error:73.776:zy_updateWWANPackage:1331:Error: zy_updateWWANPackage, Flash isn't a WWAN Package!
cp: can't stat '/tmp/search_dyn_setkey_db': No such file or directory
handler_thread.c-handler_loop()-186:received unknown event 0x10000250
grep: /etc/iproute2/rt_tables: No such file or directory
ifconfig: usb0: error fetching interface information: Device not found
@ Add device start @
@ Add device end @
wlctl: Not Permitted
wlctl: Undefined error
Setting SSID: "webmario"
Setting SSID: "ZyXELE9092_Guest1"
Setting SSID: "ZyXELE9092_Guest2"
Setting SSID: "ZyXELE9092_Guest3"
Chanspec set to 0x100b
wlctl: Unsupported
httpd:error:112.565:createHttpsCert:3432:Failed to set mgmObj, ret = 9008
ifconfig: usb0: error fetching interface information: Device not found
ZyXEL SBG3300
Login: